Mace 80355 Manuel télécharger pdf

1. Antenna Jack

2. Antenna

3. LCD Display

4. Speaker

5. REC. /Play LED

6. Battery Low LED

7. DC Power LED

8. Numerical Keys

9. MIC

10. Line jack

11. Telephone jack

12. DC 9V Power Jack

13. Buzzer

14. Reset button

Overview

1. When the door/window sensor or motion detector is triggered, it sounds an alarm

and sends a signal to the control unit.

2. The control unit dials the rst telephone number of your programmed list.

3. The person answering the call will hear the prerecorded alert message.

4. That person will have the option to listen in on the room, broadcast their voice

through the control unit, or disarm the system.

5. If there is no answer, or if the person does not disarm the security system, the unit

will dial the next number on your programmed list.

Wireless Home Security System

Product Manual

(Model #80355)

Control Unit Description

INSTALLATION INSTRUCTIONS

During set-up, if no key is pressed for 15 seconds it will come out of the setup mode and

you will have to start over. You should rst read the instructions before keying them in,

so that the unit will not time out.

See macebrand.com for troubleshooting information.

SAFETY TIPS

• Do not expose the system to direct sunlight or rain.

• Never place the unit close to your ear.

• Keep the unit away from radiators, heating ducts and stoves.

Do not permanently mount any of the pieces until following the testing directions to deter-

mine if the wireless system can communicate with all of the sensors.

STEP ONE: INSTALL THE CONTROL UNIT

1. Remove the screw of main unit from battery compartment cover. Install a 9V battery

and replace cover. This provides back-up power in case of power failure. (Fig.1)

2. Plug the antenna into the plug labeled “ANT.” on the side of the unit. (Fig.2)

3. Connect the included phone cord to the jack on the control unit labeled “LINE.” Connect

the other end of the cord to your wall jack. (Fig. 3a)

4. You can also connect a phone to the unit by plugging it into the “TEL” jack. (Fig. 3a)

Check to see if you have a dial tone.

5. Plug the AC adapter into the DC9V socket on the control unit. (Fig 3b)

PAGE 1

1 2 3 4 5

Product Manual 1

Résumé du contenu

Page 1 - Product Manual

1. Antenna Jack2. Antenna3. LCD Display4. Speaker5. REC. /Play LED6. Battery Low LED7. DC Power LED8. Numerical Keys9. MIC10. Line jack11. Telephone j

Page 2

STEP TWO: PROGRAM THE CONTROL UNIT1. Change the default password by pressing “000” followed by the [PROG] button. “Pass-word” will be ashing. Press

Page 3

STEP SIX: PROGRAMMING THE TELEPHONE NUMBERS We recommend using your cell phone as the rst person on your list. Make sure you have permission from e

Page 4

Auto Call Feature The Auto Call feature is the part of the security system that calls the programmed phone numbers if the sensors are triggered. By d

Page 5

Entry Delay timeThe control unit has been set for a 20 second delay. You can change this to 0, 5, 10, 15, or 20 seconds. 1. Enter your password foll

Plus de documents pour Systèmes de contrôle d'accès de sécurité Mace 80355

Mace 80355 Manuel (12 pages)

Voir le document Mace 80355 Manuel d'utilisateur

Mace 80355 Manuel d'utilisateur (37 pages)

Commentaires sur ces manuels

Pas de commentaire

Mace 80355 Manuel

Naviguer en ligne ou télécharger Manuel pour Systèmes de contrôle d'accès de sécurité Mace 80355. Mace 80355 Product manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Systèmes de contrôle d'accès de sécurité Mace 80355

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Mace 80355